What settings for Snow Performance Stage 2?

[askoncemore]

I have a Stage 2 Snow Performance kit with the progressive controller.

What nozzle and Start/Finish setting is everyone using?

I plann on using 50/50 WM.

 

[FLSHO21]

What settings did you end up using? I plan on installing my kit this weekend or next and I also have Torries tune...

 

[wasinger3000]

I run 90%M 10%W by weight not volume. 10 gph nozzle, turn on is at 7psi, full at 10 psi  I think. But I'll double check.

 

[askoncemore]

I have about the same settings but run 60/40 in my factory ww container

 

[wasinger3000]

I have about the same settings but run 60/40 in my factory ww container

Why not step up the meth %? Worried about fire?

 

[askoncemore]

I need to see how flammable the mixture is.
It is also difficult to get meth in CA.
Right now I use Heet and distilled water.

 

[askoncemore]

wasinger3000,

Who's nozzle are you using?

 

[wasinger3000]

wasinger3000,

Who's nozzle are you using?

Im using this one. I use it because it is recessed to allow the spray to be atomized better before hitting the air stream. I mounted it flush with the intake tube as well.

Hows your kit doing?

I think anything over 51% meth is flammable, i use 90% now and i worry about the thin plastic hose bursting under high heat so im going to upgrade to the braided hoses before my 3800 mile trip this summer.


http://www.ebay.com/itm/Water-Meth-Methanol-Alcohol-Injection-Nozzle-Fuel-Jet-Injector-9-GPH-567-ml-min-/261412891021?hash=item3cdd6c298d

 

[askoncemore]

Are you running the snow kit with the Alcohol Injection Systems nozzle?

I was looking at that nozzle and wondered if it fits the Snow nozzle holder.

 

[wasinger3000]

Are you running the snow kit with the Alcohol Injection Systems nozzle?

I was looking at that nozzle and wondered if it fits the Snow nozzle holder.

I'm almost 100% sure they all use the same threads. I'm using the Devils own nozzle holder and that nozzle I linked. So it should work.

 

[askoncemore]

I am now running the 625 ml Snow Performance nozzle with 80% meth.

Torrie just sent me a revised tune for the increased meth %.

I think the 625 is a little much.  Going to test it out this weekend.
Might switch to the Alcohol Injection Systems nozzle for less flow and better atomization.

Soon I will be going to a steel braided line for the pressure side of the pump.

I now have a small fire extinguisher in the back of the Flex... hopefully I won't need it.

 

[wasinger3000]

I am now running the 625 ml Snow Performance nozzle with 80% meth.

Torrie just sent me a revised tune for the increased meth %.

I think the 625 is a little much.  Going to test it out this weekend.
Might switch to the Alcohol Injection Systems nozzle for less flow and better atomization.

Soon I will be going to a steel braided line for the pressure side of the pump.

I now have a small fire extinguisher in the back of the Flex... hopefully I won't need it.

Same here. I have a fire extinguisher in my trunk for that moment.

I need to upgrade my lines to braded as well before I drive though death valley this summer. I'm afraid the hose will burst under high heat.

Let me know how the new nozzle works out.

 

[Wojomojo]

I'm also running the biggest nozzle provided in the snow kit and doing a 80% blend. I think it's a pretty sweet setup. I love the pull. I have used like 3-4 gallons of methanol in less than a month, but Dang has it been worth it! Thing hauls! If a smaller nozzle with better atomization makes more power then I'm open to changing!

P.S. I have stage 2 and running 8 psi as a turn on and 12 for full pump. It works pretty well. Only turns in when I really want to get on it, which is what I want anyway.