Meth injection w/ wastegate mod?

[8nutz8]

It may very well be possible that the wastegate mod isn't needed when running meth. But the point of this thread was to discuss the feasibility of running both in conjunction. Until someone does real world tests, we'll never know for sure.
Looking through Polski's meth thread . . it seems there's a tiny bit of room after the noisemaker/wastegate location to place a nozzle.
http://polskifacet.dynu.com:55698/uploader/uploads/Pictures/SHO/Meth/meth2-1.jpg
http://polskifacet.dynu.com:55698/uploader/uploads/Pictures/SHO/Meth/meth2-3.jpg

Would meth still escape in the pictured location being just slightly after the wastegate?

 

[8nutz8]

here's a pic of the location on my specific  setup just to provide a visual of the space between nozzle location and wastegate

Sent from my iPhone using Tapatalk

 

[StealBlueSHO]

My nozzle is almost exactly there but under it... it's in front of the noisemaker but before the sleeve.


Sent from my iPhone using Tapatalk

 

[J-Will]

It may very well be possible that the wastegate mod isn't needed when running meth. But the point of this thread was to discuss the feasibility of running both in conjunction. Until someone does real world tests, we'll never know for sure.
Looking through Polski's meth thread . . it seems there's a tiny bit of room after the noisemaker/wastegate location to place a nozzle.
http://polskifacet.dynu.com:55698/uploader/uploads/Pictures/SHO/Meth/meth2-1.jpg
http://polskifacet.dynu.com:55698/uploader/uploads/Pictures/SHO/Meth/meth2-3.jpg

Would meth still escape in the pictured location being just slightly after the wastegate?

It is more than feasible, use a direct port setup

Sent from my Nexus 6P using Tapatalk

 

[ddlopes]

Here's the wastegate mod on my hot pipes. I'll be placing the nozzles after the waste gate mod. Hopefully I don't get meth blowing out the wastegate.

 

[SHO9987]

here's a pic of the location on my specific  setup just to provide a visual of the space between nozzle location and wastegate

Sent from my iPhone using Tapatalk

Just thought I would share that I am currently running water/meth with the wastegate mod.  I added the w/m to help with the intake temps.  Brad reported that I was getting intake temps in the 160s when we were tuning with the E20 (80-90degree days).  I still run E20 for now and have not had Brad optimize my tune yet.  In my case I am running windshield washer fluid w/ only 30% meth and the number 5 nozzle from snow (375ml/min I believe).  My intake temps are now 107 - 117 during my pulls.  I have not noticed any issues with over spray or misting coming from the wastegate mod.  Even though wastegate is bleeding off that extra boost, the majority of the air is still going into the intake tract.  I have my nozzle mounted in the same spot you were planning on putting yours, just on the underside of the intake pipe.

 

[8nutz8]

here's a pic of the location on my specific  setup just to provide a visual of the space between nozzle location and wastegate

Sent from my iPhone using Tapatalk

Just thought I would share that I am currently running water/meth with the wastegate mod.  I added the w/m to help with the intake temps.  Brad reported that I was getting intake temps in the 160s when we were tuning with the E20 (80-90degree days).  I still run E20 for now and have not had Brad optimize my tune yet.  In my case I am running windshield washer fluid w/ only 30% meth and the number 5 nozzle from snow (375ml/min I believe).  My intake temps are now 107 - 117 during my pulls.  I have not noticed any issues with over spray or misting coming from the wastegate mod.  Even though wastegate is bleeding off that extra boost, the majority of the air is still going into the intake tract.  I have my nozzle mounted in the same spot you were planning on putting yours, just on the underside of the intake pipe.

Awesome! thanks for chiming in. I figured that nozzle location would be just fine. Has Brad expressed any concern that you meth distribution is uneven or changes when the wastegate opens?
If you have a log handy i'd love to see it to analyze.

 

[StealBlueSHO]

here's a pic of the location on my specific  setup just to provide a visual of the space between nozzle location and wastegate

Sent from my iPhone using Tapatalk

Just thought I would share that I am currently running water/meth with the wastegate mod.  I added the w/m to help with the intake temps.  Brad reported that I was getting intake temps in the 160s when we were tuning with the E20 (80-90degree days).  I still run E20 for now and have not had Brad optimize my tune yet.  In my case I am running windshield washer fluid w/ only 30% meth and the number 5 nozzle from snow (375ml/min I believe).  My intake temps are now 107 - 117 during my pulls.  I have not noticed any issues with over spray or misting coming from the wastegate mod.  Even though wastegate is bleeding off that extra boost, the majority of the air is still going into the intake tract.  I have my nozzle mounted in the same spot you were planning on putting yours, just on the underside of the intake pipe.

Sounds awesome! Thank you for the input. Obviously meth coming out of the WG-Mod is my biggest concern as I run 100%.. but if you are not getting any misting or residue then that is fantastic! Excited to see where it goes! Same with Colorado-SHOBro!

 

[8nutz8]

here's a pic of the location on my specific  setup just to provide a visual of the space between nozzle location and wastegate

Sent from my iPhone using Tapatalk

Just thought I would share that I am currently running water/meth with the wastegate mod.  I added the w/m to help with the intake temps.  Brad reported that I was getting intake temps in the 160s when we were tuning with the E20 (80-90degree days).  I still run E20 for now and have not had Brad optimize my tune yet.  In my case I am running windshield washer fluid w/ only 30% meth and the number 5 nozzle from snow (375ml/min I believe).  My intake temps are now 107 - 117 during my pulls.  I have not noticed any issues with over spray or misting coming from the wastegate mod.  Even though wastegate is bleeding off that extra boost, the majority of the air is still going into the intake tract.  I have my nozzle mounted in the same spot you were planning on putting yours, just on the underside of the intake pipe.

Sounds awesome! Thank you for the input. Obviously meth coming out of the WG-Mod is my biggest concern as I run 100%.. but if you are not getting any misting or residue then that is fantastic! Excited to see where it goes! Same with Colorado-SHOBro!

Well if we could get a hold of the OP in the for sale section and get him to sell us his meth parts i could make some progress! PM'd him twice now. . i'm guessing his car and parts are probably gone

 

[SHO9987]

Brad hasn't dived into the logs just yet.  Attached are a 1st through 3rd gear pull and then a low end 3rd gear pull up to 4th.  The system is setup to turn on 50% at about 6psi and goes full at about 10psi.